Cat flaps let your cat go inside and out at their own pace, without having to let them in or out. They can also help prevent your cat from urinating inside the home.

Installing a cat flap on a upvc door panel is a lot easier than a glass door, but it will require some expertise and the appropriate tools.

Take a measurement of the door

Fitting a cat flap in a door can be tricky but as long as you use the correct type of cat flap make sure you take your time and follow the directions provided, it should not prove to be too much trouble. We will demonstrate how much to install a cat flap to mark the shape and use a jigsaw in order to cut the door area. Then we will finish the job by affixing the flap. This will ensure that the flap remains in place and shields the door from rain and wind damaging the door.

The first thing to do is measure the width of your pet in order to get an accurate measurement of what size of cat flap you'll need. This will enable you to select a flap that is large enough for your pet to walk into the house and exit without needing to open the door every time.

Once you have the measurements, you can determine the location on the door where the template should be positioned, usually this is done with an X, however some kits include drawings that show the location to drill, if you have one, then attach it to the door and use a pencil to draw around it. If your door has a moulding or sill on the bottom edge of it ensure that you have enough clearance from these as this will keep your cat safe and will prevent them from getting access to your home.

Set a square to check that you are cutting correctly and to make sure the hole is in a rectangle shape. When you are satisfied with this, you can begin to remove the remaining door material. Set the square with a ruler to ensure that you're cutting the material correctly and that the hole is a rectangle shape. Once you are satisfied with the result, you are able to remove the remaining door material.

Draw a Line

The cat flap in upvc door panel - http://wiki.iurium.cz - flap is a great way to allow your pet to go in and out without worrying about them being a nuisance to a visitor, or leaving unwanted gifts in the house. It also stops draughts and helps keep your home's temperature stable. The installation of a cat flap your door may seem daunting for those who haven't attempted it before. A lot of people will hire an expert carpenter or joiner to complete the work. This is an option but you can do it yourself if your tools are appropriate and the steps are adhered to.

This is much easier to do with wooden doors, but it is possible with uPVC. However it is important to be cautious not to scratch the doors as this could make it impossible to claim your warranty. The first step is to measure the door to ensure that it can accommodate the new cat-flap. If you have a standard uPVC panel it's easy. However when your door is made of composite or another kind of door, you may require more care.

Next, you will need to determine the height of your belly for your cat. This is the height between the floor and the bottom of your cat's stomach. You will need to locate a space at the entrance that will allow your pet to move through easily. Once you have this information you'll need to mark out the area using pencil and a spirit level to ensure that the hole you will create will fit your cat.

Once you have marked out the area, it is time to cut out the hole. It is important to be patient and use a jigsaw to ensure that the cuts are smooth and clean not rough and uneven. This could cause damage to your door. You should also remember to wear safety glasses and a dust protection mask whenever working with the jigsaw as inhaling the sawdust could be hazardous to your health. Once you've finished cutting the hole, you will require sandpaper to smooth the edges so that the cat flap is easily inserted into the hole.

Make a hole

Getting a cat flap fitted into an existing door panel or double glazing sealed unit can be quite difficult. You might be tempted to tackle the task yourself, but unless have expertise in DIY, it's recommended to hire an expert to complete the task for you. A faulty job can not only be ugly, but also pose an security risk. It could let cold air to enter when the cat is outside and hot air out when the cat is inside.

The first thing to do is mark out the position of the hole in the door with a pencil and a spirit level. This will ensure that it is properly located and is parallel to the other parts of the door. You should make sure you have a piece of sandpaper at hand to smooth out any rough edges.

Wear any safety equipment you need to work with an electric tool. If you're worried about noise, you can buy a jigsaw with a cord that is quieter and easier.

It is essential to only cut away the material that is required to fit the cat flap. A little bit of extra material will be needed to cover the thickness of the the cat flap itself but removing more than this can cause problems and even harm the frame of the door.

A door made of upvc could include a metal frame, or panel within it which could block the microchip cat flap insulation flap if this is the case you'll need to make an oversize hole to ensure the metal does not touch the wall of the cat flap. If this is done, it is essential to fill in the oversize gap and render it watertight.

If you're looking to install a cat flap in a double-glazed or upvc window with frames made of metal, you'll need to consult an expert. They will provide you with a new piece of glass with the hole already pre-made for the cat flap. This will be cheaper than fitting a cat flap inside an existing pane of glass that was not made for this purpose.

Fit the Flap

Cat flaps give your pet the freedom to go and come anytime they want, allowing them to relax in the home whenever they want to. However, if you own a uPVC door it can be difficult to fit a cat flap, particularly if you don't own glass panes that could be cut to fit one. If you're able to purchase and install a new half-glazed uPVC panel then it is possible to fit the cat flap to these doors. It's not as simple as just cutting a hole through the door however, and there are a few things you'll need to do first to make sure it's safe.

A composite, uPVC, or GRP door panel is usually comprised of a thin plastic skin which is bonded to an insulating polystyrene core. The material is extremely fragile and care should be taken when cutting through it to avoid causing damage. This type of door typically includes a template which you can use as a guide to cut the hole in the door.

Once you have marked the location of the hole in your door, it's now time to install the flap itself. You can purchase and install a wide variety of different models, from basic push-button operated ones to ones that are activated by microchips that only let in your pet. No matter which type of cat flaps you select it's essential that your cat can utilize the flap with ease without getting stuck in bad weather.

A circular fitting a cat flap in a upvc door is superior than a square, because circles can be cut more securely into the glass. It's because square holes are more likely to crack the glass when drilled. This is also a safer choice, as you won't have to drill into the toughened glass which could break and cause harm to your pet or family. This is particularly important if there are children or elderly people in your home who could be hurt by glass shattering.