How to Repair Car Keys

Car keys might seem small and insignificant, but they are crucial to the operation of your vehicle. The cost of replacing a traditional or modern transponder car key repair company keys can be upwards to $200.

However, there are ways to repair your mobile car key repair keys at home for only a fraction of the cost. This article will discuss the most frequently encountered car keys issues and their DIY solutions.

Dead Key Fob Batteries

Cars are equipped with a remote key fob which makes opening doors and trunk easier than ever before. The battery inside the device is prone to dying. There are a few tricks you can use to solve this issue quickly.

First, check if the car is in ignition mode. If it is, then the battery on the key fob could simply be low instead of dead. To test this, press the button on the key fob straight up against the vehicle's ignition button. If this works, then the battery is probably fine and needs to be changed.

To replace the battery within the fob, the case open using a screwdriver. Be careful not to apply too much pressure because this could cause the fob to split into two pieces. If the fob won't open, try using your pry tool more than once around the outside of case.

Open the electronic portion of your car after you have removed the mechanical key. Install the new battery and snap back the shell. If your key fob still isn't working after this procedure, it could be a larger issue with the remote start system in your car. This requires an expert to determine the cause. A reputable mechanic will in a position to assist you in this situation. If you need help with your car, you can contact roadside assistance.

Broken Key Ring

There are a few options that you can do in the event that your key fob won't work because the ring has been broken. Check to see if you can locate the broken part inside the ignition. If it's still there it, remove it without damaging the ignition lock or the door lock. Call a locksmith if you are having trouble taking the key off. They have tools that can safely remove a damaged key from the ignition.

Another reason that can lead to broken car keys repairs keys is corrosion on the circuit board or frame. You can clean the circuit board using the help of rubbing alcohol and a cotton swab. This will remove any corrosion and ensure that the contact pads don't get damaged.

If your key isn't working because the ring is broken, you may be able to fix it using a sturdy wire or nail to seal the hole. Superglue can be used to repair a broken key ring. First, clean the broken rings with a damp cloth and then apply a small amount superglue on each end of the wire or nail. Let the pieces dry and then press them into place. These DIY solutions might seem appealing, but they're just an interim measure. It is best to employ an experienced locksmith for long-term repairs. They have the knowledge and tools to repair car key (More) damaged keys quickly and effectively. They can replace the battery and reprogram the key fob in the event of need.

Broken Key Blade

Some key blades might break due to wear and tear. If this happens, it's time to buy a new key. This problem isn't nearly as serious as you believe at first. The primary issue is that the blade snapped off the case.

Spraying lubricant into the keyhole is one method to fix the problem. Then, you can use pliers tweezers, or a pin to grab the end of the broken key and take it out. You could also employ a magnet in the event that the key is magnetic. Use a magnet to assist you remove the key, but take care to not break the tumbler of the lock.

Call a locksmith immediately if you are unable to remove the broken piece of the key. They have special tools to safely extract keys without causing damage.

Super glue can be used to fix the snapped lock. Apply a small amount glue to the edges of the break and press them together. Wait until the glue has dried before inserting the key into the lock. This method isn't secure and you may need to repeat the process a few times before it works. Super glue may not hold the key together. This is more of a temporary measure than an option that can last.

Broken Plastic Loop

If your key fob's plastic loop breaks off it could render the key useless. It's a fairly simple fix. To replace it alternative, you can use a thick wire or finishing nail. Drill two holes into the broken plastic loop for each end of the nail or wire. Cut the nail or wire to a key width, then place the superglue drop in each hole. Then, press the wire or nail into the holes until it closes them and let it dry.

Another option is to purchase an alternative shell from a locksmith who sells them. They can take the programmable part of your key, move it to the new shell, and cut an entirely new blade for less than the full replacement cost.

This is not the best solution, but it will get you on the road again if your key split in half. However, it could be difficult to repair the key blade if it's in the ignition. You can try using hair clips, a needle or an extractor tool to remove the damaged part out of the ignition, but this is risky if you're not cautious. The best choice is to call an expert locksmith who has tools to safely remove broken keys from the ignition. You can also request an entirely new key made using the correct cuts to fit the ignition of your vehicle.

Broken Master Key

If a key gets damaged inside the lock, you'll need to try to retrieve it before it gets completely destroyed. There are a variety of methods you can use, including using lubricants and tools like needle nose pliers or tweezers to take a small piece of the damaged key and pull it out.

To start, spray the inside of your lock with a lubricant like graphite powder or WD-40. You can also employ the hacksaw blade technique that involves sliding the blade along the sides of a broken key and grabbing onto some of its teeth. If you're successful you will be able to cut the damaged key.

Many hardware stores offer tools for key extraction that spiral. This has a thin flexible bar with spiral threads which can be inserted into the keyway, and then bent to get into the broken part of the key. Once it has hooked onto the serrations, you can twist it in a circular motion, and press it against the broken part of the key to get it out.

It's worth trying to remove a broken master key before calling a professional locksmith. If you're not able to take the broken piece off it's time to contact a professional locksmith. A locksmith can give you an entirely new key that will be programmed to the transponder in your car remote key repair.