Car Key Button Repair

A broken car key button can be frustrating. You might need to contact the 24 hour Locksmith Service or purchase a replacement remote.

You may be able save money by repairing your old key fob instead of replacing it. This is particularly true if the problem is due to a worn switch or faulty contact.

Battery

If the buttons on the key fob aren't responding to pressing the buttons, it could be an obvious sign that the battery is dying or nearing the end of its lifespan. Fortunately, replacing the battery is a simple task that you can complete on your own instead of paying a locksmith or dealership to do it for you.

Find the battery compartment first. The battery compartment is usually located on the back of the key fob, and may be hidden behind a cover which slides out or an open button that opens the access point. Once the compartment is opened, locate the small button cell battery. It's usually shaped as coins and marked with the plus and minus signs. Remove the old battery and replace it with a new one. Make sure that the plus and the minus symbols are properly aligned.

Close the compartment and snap the two halves of your key fob. Make sure you align the parts and secure them correctly prior to closing the door and testing your keys. Press any of the buttons to verify that they work properly.

If the remote keyfob isn't working after replacing the battery, there could be other problems that require a different type of repair. Dropping the fob in a puddle could cause it to stop functioning. It could also be due to a malfunction with the internal electrical system, or it may need to be deprogrammed. Try to figure out if the issue is with your mobile key repair fob by using these other methods for troubleshooting your car keys repairs near me.

Switches

There are many kinds of switches found in the car key fob according to the year and model. The older style key is equipped with an electronic chip that is visible inside the case. The latest keys operate by sending signals to your car. The buttons on a key repair service may be damaged or worn out by regular use, irrespective of the model. The result is they become difficult to press or even unresponsive. If you try to force the button to function it could cause further damage and potentially stop the key from being able to start your vehicle in the future.

If your key doesn't appear to be working, first try changing the battery. If this doesn't work, you might need to clean your key fob or re-adjust its switches. Because these tiny electronic switches spend a lot of time being moved around they are more prone to wear out than larger parts of your key.

The switches have a rubbery feeling and are coated with an electrical conductor. This film can be worn away over time. Fortunately, they are also tiny and inexpensive to replace. They're soldered on the circuit board, therefore it is important to take them off without damaging other components. You can then solder new ones into and reassemble your fob.

A good way to keep your car key fob from being damaged is to avoid using it for longer than a couple of hours at a time, and to avoid leaving it in visible locations that it will be visible. Also, you should locate a safe place to store your keys when you're not using it.

If you've tried cleaning your key fob or replacing the battery, and the issue continues to persist it's time to think about hiring a locksmith. A professional locksmith can test your key's frequency to see whether your vehicle is capable of communicating. They can also open and replace microswitches, change cases, and much more.

Outer Case

If the buttons aren't able to move freely in the case, they could become stuck or break. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it may be necessary to take off the case. If the contacts that the buttons touch aren't fitting well or are worn out, adjusting them may be the only way to fix the issue.

Some keys use buttons made of rubber, which wear out over time. Rubber buttons can become hard to press as they stretch, and nails could scratch them. In this case the key repair shop near me may fail and it's time replace the case or the buttons. This repair involves disassembling your remote, locating the buttons on the board, heating the solder and carefully remove them. New buttons are then soldered to the circuit board. The case is then put back together with the horseshoe key repair car blade piece inserted. The new buttons must be snugly fitted into the case to prevent them from falling out.

Inner Case

Since your key fob is likely be tossed around and occasionally be pressed by accident and the buttons inside may become stuck or broken over time. Utilizing metallic tape and a hole punch, you can usually solve this issue when your car is not at home and the key fob won't work and you are unable to open the doors, but not start the engine. This quick fix may allow you to return safely to your vehicle to complete your trip.