How to Repair Car Keys

Car keys may seem tiny and insignificant, however they are essential for the proper operation of your vehicle. The cost of replacing the traditional or contemporary transponder car key repair can range from $200 to upwards of $200.

There are methods to repair your car keys at home for a fraction of the cost. This article will address the most common car keys issues as well as the DIY solutions to fix them.

Dead Key Fob Battery

The remote key fobs for keys that come with cars make it simpler than ever to open the trunk, doors, and the tailgate. However, the battery inside the device could die. There are a few tricks you can use to resolve this issue fast.

Examine if your vehicle is in ignition mode. If it is, the battery on the key fob could be drained instead of dead. To test this, push the button on the key fob towards the ignition button. If this is successful, the battery is probably in good condition and will only need to be replaced.

To replace the fob's battery, first pry open the case with an instrument like a screwdriver, or watch-type tool. Be cautious not to apply too much pressure as this could cause the fob to break into two pieces. If the fob doesn't open try prying the tool more than once around the outside of the case.

Open the electronic portion of your car once you have removed the mechanical key. Insert the new battery and then snap back the shell. If the key fob isn't working after this, there could be a larger problem with the remote start system that requires a professional diagnosis. If this is the case, a reliable mechanic should be able help you. If you require assistance with your vehicle, you can contact roadside assistance.

Broken Key Ring

There are a few options to do when your key fob does not work because the ring is broken. First, you should check to see if your broken piece is still in the ignition. If it is, you should remove it without damaging the door lock or ignition lock. If you're having difficulty removing it, call an expert locksmith. They have the right tools to safely remove a broken key from the ignition.

A broken car key can also be the result of corrosion on the plastic frame or circuit board. Clean the circuit board using rubbing alcohol and a cotton swab. This will eliminate the corrosion and prevent damage to the contact pads.

If your key isn't working because the ring is broken it, you might be able to keyless entry repair it by using a thick wire or nail to seal the hole. Superglue can be used to repair keys near me damaged key rings. After cleaning the ring with a moist cloth Apply a small amount superglue to the ends of the nail or wire. Allow the pieces to dry, and then press them into place. These DIY solutions might seem appealing, but they are only a temporary measure. It's best to hire an expert locksmith for repairs that last. They have the experience and tools to repair damaged keys quickly and efficiently. They can even replace the battery inside your key fob and reprogram it if needed.

Broken Key Blade

Some key blades may break due to wear and tear. If this occurs, you must purchase a new one. This problem isn't nearly as serious as you think at first. The main problem is that the metal blade has snapped away from the case.

One solution is spraying the key hole with a fluid that lubricates the key hole. Then, you can use pliers, pins, or tweezers to grab the broken end of the key and take it out. If the key is magnetic, you can also use a magnet to help pull it out. Be careful not to use a magnet on an ignition key since it could cause the tumbler in the lock to break.

If you are unable to get the broken piece from the key, contact a locksmith right away. They're equipped with special tools to safely extract keys without causing damage.

You can also use super glue to repair a snapped key. Apply a small amount of the glue to the edges and press them in. Then, wait until the glue is dry before inserting your key into the lock. But this method isn't very reliable and you may have to repeat the process a few times before it works. In addition the super glue might not be enough strong to hold the key together. This is more of a stopgap measure than a permanent solution.

Broken Plastic Loop

If the plastic loop on your key fob is damaged it can cause the key to become useless. Luckily, this is a fairly easy fix. As a replacement alternative, you can opt for wire that is thick or a finishing nail. Drill two holes into the plastic loop that is broken at each end of the wire or nail. Cut the wire or nail into a key width, and then place one drop of superglue into each hole. Then, press the wire or nail into the holes to seal them and allow it to dry.

A locksmith who sells replacement shells is a different option. They can transfer the programmable part of your key to the new shell and cut an entirely new blade at a fraction of the cost.

This isn't the most efficient solution, but it will help you get back on the road once more if your key split in half. It's difficult to fix when the blade of the key is in the ignition however. If you are not careful you could employ a hair clip, or a needle to remove the damaged part from the ignition. The best solution is to call an expert locksmith who has tools for safely removing damaged keys from the ignition. You can also have a new key made with the proper cuts to fit the ignition of your car.

Broken Master Key

You'll have to attempt to retrieve the key before it is completely destroyed. There are a variety of methods you can use, including using lubricants as well as tools such as needle nose pliers or tweezers to pick up a piece of the key that has been broken and pull it out.

To start, spray the inside of your lock with a lubricant, such as graphite powder or WD-40. You can also employ hacksaw blades, which involves moving the blade across the face of a broken key and then grasping a few of its teeth. If you're successful you will be in a position to remove the broken key.

Many hardware stores sell tools for key extraction that spiral. It is a thin, flexible bar with spiral threads, which can be put into the keyway and bent to dig into the broken section of the key. Once it is firmly anchored to the serrations, you can twist the bar around and pull it against the damaged section of the key.

Before calling a locksmith, try to get rid of the broken master key. If you're not able to get rid of the broken piece, you'll need to call a locksmith. Locksmiths can create you an entirely new key that will be programmed with your car transponder.