Car Key Button Repair

A broken car key button can be a source of frustration. It is possible to call a 24-hour Locksmith Service or purchase an alternative remote key fob repairs.

You may be able save money by repairing your old key fob instead of replacing it. This is especially true if the problem is caused by a worn switch or faulty contact.

Battery

If the buttons on your key fob aren't responding to pressing it, it could be an obvious sign that the battery is dead or nearing the end of its lifespan. It's easy to replace the battery yourself, rather than paying for a locksmith or dealership.

First find the battery compartment. The battery compartment is usually located on the back of the key fob and can be hidden behind a cover that can slide out or a button that opens the access point. Once the compartment is exposed then you will find the small battery. It's usually shaped as an oblong coin and is identified with a plus and minus sign. Remove the battery from the old one and insert a new one in its place, making sure that the plus and minus symbols are properly aligned.

Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the components in place. Press any of the buttons to confirm that they function correctly.

If the remote key fob repair near me keyfob isn't working after replacing the battery, it could be other issues that require a different type of repair. Dropping the device into a pool of water can cause it to cease functioning. It could also be a problem with the internal electrical system, or it may need to be deprogrammed. Check out these other common automotive key repair troubleshooting methods to determine if your key fob is having a problem of its own.

Switches

Based on the year and manufacturer, there are various kinds of switches available on the keyfob of your car. The older style keys have an embedded chip that can be seen in the case. The newer keys work by sending signals to your car. The keys' buttons can be worn out or damaged by regular use, irrespective of the model. This causes them to become difficult to press or even ineffective. If you try to force the button to work, it can cause further damage and may even stop the key from starting your vehicle in the future.

If you can't get your key to work, try changing the batteries. If this doesn't work, you might need to clean your key fob or adjust the switches. These tiny electronic switches are more likely than the larger parts of the key to break because they are constantly tossed around.

The switches are made of rubber, and they're coated with an electrically conducting film that wears down over time. Fortunately, they are also tiny and easy to replace. The old ones are soldered onto the circuit board, so you'll have to take care to remove them without damaging anything else. Then, you can solder the new ones in and put them back together.

One way to prevent your car remote key repair near me key fob from getting damaged is to avoid using it for longer than a couple of hours at a time, and to avoid leaving it in visible locations that it will be visible. If you don't use your auto key fob repair, store it in a safe place.

If the issue continues to persist after you've cleaned your key fob or battery, and tried to clean it, then you might need to contact a locksmith. A professional locksmith can test your key's frequency to see if your vehicle is still able to communicate. They can also open and replace microswitches, change cases, and more.

Outer Case

Key fobs spend much of its time bouncing around and when the buttons aren't allowed to move between the case they can get stuck or broken. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it could be necessary to remove the case. If the contacts that the buttons touch aren't suitable for the application, or if they are damaged, adjusting them could be the only solution.

Rubber buttons may wear out over the years. The rubber is stretched and nails pierce it, and the buttons become difficult to press. This could cause the key to fail, and Fully comprehensive in this case it is time for the replacement of the case or buttons. This repair involves disassembling your remote, finding the button switches on the board, heating the solder, and carefully removing them. The circuit board then gets soldered with new buttons. The case is then reassembled and the horse shoe key blade piece attached. The new buttons must be a close fit inside the case to avoid them from falling out.

Inner Case

Over time the buttons on your key fob may be damaged or stuck due to the continuous rubbing and accidental pressing. Utilizing metal tape and a hole punch, you can often quickly solve this issue when your car is away from home when the key fob doesn't work, allowing you to unlock the doors, but not start the engine. This simple fix can enable you to safely make it back to your vehicle and complete your journey.